Benchmark Reviews Discussion Forum Right Header

Go Back Benchmark Reviews Discussion Forum > Hardware > Overclockers Lounge

Overclockers Lounge Post your projects and results in this section.

Reply
Thread Tools Display Modes
#1
Unread 31st August 2010, 09:06 AM
D.John D.John is offline
Bit
Join Date: Aug 2010
Posts: 1
MAX COOLING without THERMAL PASTE

THERMAL PASTE ALTERNATIVE FOR MAX COOLING.

From an engineer, who is not an overclocker
CPU= Basically an, assy of silicon wafer / board / terminals, topped of with a metal cover and filled with resin. And then plug it in and get it gets hot.
With multi core processors the ‘hot spot’ can move, I guess a thermal map of the metal cover would look like something off the 5-day weather forecast. During this heating the metal cover ‘et-all’ is not going to thermally expand evenly. Try heating up a biscuit tin lid with a candle (boi’ng). To some extent the base of the heatsink will also want to do its own thing.

So You have lapped the mating CPU / heatsink surfaces so flat and finely that you could shave in them (nice one!), then add some thermal paste, screw it down nicely, and then set about revving the nuts of it. (Ever thought about hot lapping?).

The variable amounts of thermal expansion, due to the ‘thermal map’ and dissimilar metals are going to alter the contact pressure and geometry. Perhaps even create a localised gap in the mated surfaces, a gap less than a tenth the thickness of a cigarette paper is a chasm for heat conduction, (will the thermal paste flow to take up the void). If it wasn’t for the delicate electronics I would braze them together, (ok) So no heating above CPU max,T.-- How about fluxed liquid metal say mercury, it might work, but would be dodgey and problematic. So what’s left regular solder is to hot. Why not try Woods or Fields metal (wiki) you can melt them in a cup of tea, or 62 – 70 deg C to be precise, these alloys are a couple from a whole group of Low Melt Alloys, how about LMA.

How to apply ‘LMA Technology’

Shopping list:
Small amount of LMA, Suitable non-corrosive flux, A couple of thyristors calibrated to LMA melting point. A hairdryer.

Method:
Flux and ‘Tin’ and hot wipe the heatsink and CPU mating surfaces (note: aluminium probably bad /copper probably good). Remove any excess LMA from edges.

Install CPU and mount the small thyristors on side of metal CPU case and test by warming case. Ok that works.

Assemble heatsink with CPU applying a thin smear of flux on both tinned surfaces, but don’t fully tighten down heatsink.

Warm up heatsink with hairdryer until the thyristor readings show that the LMA melting point has been exceeded by a couple of degrees or so. Torque up heatsink and then cool things down (now for the science bit, use the hairdryer without any heat).

It would be an idea to trial run the heatsink warm-up before tinning as you will already have the calibrated thyristors hooked up to your multimeter. To calibrate thyristors flatten a drinking straw and seal up one end, insert hooked up thyristors into straw and tape straw to an accurate mercury thermometer the thyristors beside the thermometer’s bulb, and suspend in a glass or jug of hot water and take readings as the water slowly cools.
What Flux?? suggestions!.
Note- if CPU operational temp went above LMA melt point and oxidation was not present the LMA would re-flow, as long as excess LMA is not present this could be a good thing, settling thing in?

Any Takers
Regards
Dom
Reply With Quote
Sponsored links
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Crucial Ballistix Thermal Sensor Memory Kit Review Olin Coles Article & Review Forum 0 28th June 2010 06:27 PM
80-way Thermal Interface Material Performance Test Review Olin Coles Article & Review Forum 58 23rd April 2010 10:43 AM
Best Thermal paste for a HDT cooler Olin Coles Computer System Hardware 63 2nd April 2010 05:58 AM
a Megahalem on a i5 and using mx-3 paste help and how thanks meridius General Hardware Forum 3 19th November 2009 06:40 PM
33-Way Thermal Interface Material Comparison Olin Coles Article & Review Forum 41 22nd December 2008 02:22 PM


All times are GMT -7. The time now is 06:16 PM.

Benchmark Reviews Discussion Forum
Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Remove advertisements

Follow Benchmark Reviews on FacebookReceive Tweets from Benchmark Reviews on Twitter